Step 2: Once boot up, The Power and Powerline LEDs should be lit. Note: Ensure the Power Switch on the DHP-P338AV is switched ON Step 1: Plug your DHP-P338AV into your existing Powerline network. Solid: The device is connected to a Powerline network. The DHP-P338AV WILL NOT work with only a router. Important Note: The DHP-P338AV MUST be used in conjunction with at least one other Powerline device. Red: The PowerLine link rate is less than 50 Mbps Green: The PowerLine link rate is faster than 80 Mbps Note: If the Power LED does not start to flash, reset both adapters and try again- How do I reset my DHP-500/501AV adapters? The Power LED should start to flash On/Off On one of the adapters, press and hold the Simple Connect Button for 2 seconds and then release it. Reset both adapters - How do I reset my DHP-500/501AV adapters?ġ. The Ethernet LED should Light Up.Īmber: The Powerline link rate is better.ġ. Step 4: Plug the other adapter into any ethernet enabled device (Computer, TV, Game Console etc.). Note: If the Power LED does not start to flash, reset both adapters and try again- How do I reset my DHP-308/309AV adapters? Reset both adapters - How do I reset my DHP-308/309AV adapters? Off: The device has not found any other compatible Powerline devices using the same encryption key.ġ. Solid: The device is connected to a Powerline network. Off: The device is not receiving electrical power. Try different wall outlets if performance is not optimal.īlinking: The device is setting itself up after reset or simple connect button was pressed or power saving mode enabled. Note: Link rate will depend on link quality of electrical lines. Red: The PowerLine link rate is less than 50 Mbps. Green: The PowerLine link rate is faster than 80 Mbps.Īmber: The PowerLine link rate is between 50 Mbps and 80 Mbps. Step 4:Plug the other adapter into any ethernet enabled device (Computer, TV, Game Console etc.). Step 3: Plug one of the adapters into your router/existing network. The Power and Powerline LEDs should be both On. Note: If the Power LED does not start to flash, reset both adapters and try again- How do I reset my DHP-306/307AV adapters?Īfter 15-30 seconds, the Power LEDs on both adapters should stop flashing and the adapters will be secure. The Power LED should start to flash On/Off. Within 2 minutes, press and hold the Simple Connect Button on the 2nd adapter for 2 seconds and then release it. The Power LED should start to flash On/OffĢ. On one of the adapters, press and hold the Simple Connect Button for 2 seconds and then release it. Step 2: It is suggested to secure your PowerLine devices to prevent others from gaining access to your network.ġ. Improper wiring and/or circuit breakers can be the reason for this. Plug the adapters into another wall outlet. Reset both adapters - How do I reset my DHP-306/307AV adapters?Ģ. Note: If the Powerline LED does not light up:ġ. Once plugged in, the Power LED and Powerline LED should be lit on both adapters. Note: Avoid using Power Bars or surge protectors as it could result in poor performance. One of them should be in the same room as your router.ĭO NOT plug any cables into the adapters yet.
Step 1: Plug in both adapters into a wall outlet. Off:The device has not found any other compatible Powerline devices using the same encryption key. Solid:The device is connected to a Powerline network.īlinking: The device is transmitting data Off: The device is not receiving electrical power. Solid: The device is receiving electrical power.īlinking: Indicates that the device is setting itself up after reset or when the security button was pressed or power saving mode enabled. Important Note: In order to create a Powerline network, a minimum of TWO powerline devices is required.
#Dlink powerline adapter utility install
How do I set up and install my Powerline adapter or kit?
0 kommentar(er)
